Living in a vacuum: Crankcase ventilation system testing
Jun 28, 2022 · The crankcase pressure wanders between -2.5 to 4 inches of water column (-7 to 10 millibar, well below the specification for this engine of -30 millibar, plus or minus 5 millibar). If there is less vacuum in the crankcase, this would be an over-pressure condition (which means air is leaking into the crankcase).
A Solid Approach to A-Pillar Repairs | FenderBender and ABRN
Dec 31, 2019 · The most basic design of the upper A-pillar is a two-piece, inner and outer configuration that may also include reinforcements at specific locations to add strength. These locations are usually at the upper and lower ends of the windshield location. For repairs this is the simplest type of construction to repair, section or replace.
Hub bearing dos and don'ts | FenderBender and ABRN
Sep 22, 2015 · Reset the bearing and level the knuckle. When the new bearing is installed the hub needs to be pressed into the bearing. It is very important to fully support the complete bearing on the opposite side of the hub that is being pressed. This will help to ensure that the new hub is being pressed into place correctly.
How to read automotive wiring diagrams - FenderBender and ABRN
Jan 27, 2017 · Figure 4 is a typical automotive wiring diagram that shows a radiator cooling fan circuit. Two fuses (40 and 10A) power the circuit and are directly connected to the vehicle’s battery (Hot at all times). There are three relays that connect power to the cooling fans and control low and high speeds.
Honda Updates Post-Scan, Calibration Position Statement
May 23, 2019—Honda recently issued a new position statement on post-collision diagnostic scan and calibration requirements for Honda and Acura vehicles. It's the position of American Honda that all vehicles involved in a collision must have the following minimum diagnostic scans, inspections, or calibrations done to avoid improper repair.
Breaking: Axalta Former Owner Carlyle Buys Worldpac from Advance
Aug 22, 2024 · Global investment firm The Carlyle Group, which purchased Axalta Coating Systems in 2013 and later took it public, has agreed to purchase automotive parts wholesale distributor Worldpac, Inc., from Advance Auto Parts, Inc. The $1.5 billion cash transaction is expected to close before the end of the year. Worldpac generated approximately $2.1 ...
State Farm DRP Shops to be Required to use CCC
Dec 31, 2020 · The insurance company has given direct repair plan shops a spring deadline to get on the platform. Dec. 31, 2020—State Farm next year will require its Select Service collision repair shops, which are part of its direct repair program, to use CCC. Repairer Driven News first reported the development, which was announced to State Farm DRP shops ...
Weld bonding: Understanding the technicalities and the techniques
Jul 10, 2015 · Along with STRSW, the weld bonding process uses a structural metal adhesive in the middle of a joint or assembly. The STRSW can weld right through the adhesive to provide a complete, bonded interface for replacing structural or non-structural autobody panels. The adhesive significantly increases the strength of the joint.
Rear axle service simplified | FenderBender and ABRN
Jan 1, 2020 · Block the flexible brake line above the differential that splits fluid to the left and right. 4. Remove the brake line from the wheel cylinder. 5. Remove the parking brake cable from the pivot. 6. Remove the four 14mm nuts from behind the backing plate for the bearing housing. 7. Pull the axle out (shoes and all).
Diesel NOx sensor technology | FenderBender and ABRN
Jan 1, 2020 · This signal (along with the NOx sensor signal) is used by the ECM to adjust DEF dosing for maximum SCR catalyst efficiency. Benefits of the Delphi ammonia sensor include optimizing performance of the SCR catalyst, enabling the use of an optimally-sized SCR catalyst, and helping to provide SCR system diagnostics.